Big
Mouth™
Cold Air Induction
The standard system
draws warm air from a small opening in the top panel
and from a restrictive tube behind the bumper bar.
SS Inductions’ Big Mouth™ system channels
cool air from the front of the moving car - from
under the bonnet and also from the front grill area
by utilising the unique SS Inductions’ aluminium
air scoop which attaches to the air-conditioning
condenser. This extra airflow is then rammed through
the lower and front openings in the induction unit
directly to the single entry intake connected to
the standard airbox.
Expect up to 12kW increase at the rear wheels, smoother
performance, more responsive throttle and a considerable
fuel saving.
The three-part kit consists of plastic induction
unit, plastic single entry connecting intake and
the unique SS Inductions’ aluminium air scoop.
RRP $399.00.
Part # CAI007/2
|
|
Growler
Cold Air Induction
The
standard system draws warm air from a small opening
in the top panel and from a restrictive tube behind
the bumper bar. SS Inductions’ Growler system
incorporates a streamlined pod style airbox that
draws cool air from behind and beneath the headlight
and rams it through a superior long-life Big Mouth™
pod filter (manufactured by Kingdragon®, Italy).
Expect up to 16kW increase at rear wheels, smoother
performance, more responsive throttle, a considerable
fuel saving and a nice induction growl under hard
acceleration.
The four-part kit consists of plastic pod-style
airbox with lid, plastic replacement front panel
and the Big Mouth™ pod filter (which normally
retails at $170.00). RRP $599.00.
Part # CAI019
|
|
Big Mouth™
High Performance Filter
Manufactured
by Kingdragon®, Italy. These long-life washable
filters have superior airflow and maximum filtration.
RRP $125.00.
Part # PAF002
|
|
Big Mouth™
CNC Billet Airflow Meter
The
airflow meter basically measures airflow directly,
with an electronic sensor on the air stream of the
intake providing an output voltage reading that
is proportional to the mass air flowing into the
engine. The airflow meter then sends the necessary
information to the ECU, which recalculates fuel
flow and ignition timing.
The SS Inductions’ Big Mouth™ Airflow
Meter has a superior flow rate compared to standard
and a more streamlined airflow compared to a modified
meter. It uses the original centre with the electronic
sensors from your standard airflow meter to ensure
there are no engine management problems.
The resulting changes to the air/fuel ratio and
ignition timing mean a noticeable power gain (up
to 12kW at the rear wheels) and a considerable saving
in fuel consumption. This is a non-exchange item
that enables the original meter to be retained.
RRP $445.00.
Part # AFM111
|
|
Intake
Pipe
The standard
pipe connecting the airflow meter and throttle body
is very small in diameter and has inner ridges that
disrupt airflow.
The SS Inductions’ intake pipe is a three-piece
high volume plastic pipe with flexible rubber ends.
The increased air mass ensures improved throttle
response while the inner smoothness is less disruptive
to the airflow at all speeds. RRP $185.00.
Part # ITP001
|
|
Big Mouth™
CNC Billet Throttle Body
The
standard throttle body has a 74mm butterfly and
is very restrictive.
The SS Inductions’ Big Mouth™ Throttle
Body with its 78mm butterfly delivers greater torque
and throttle response through the entire rev range.
Expect an increase of up to 8kW at the rear wheels.
The kit includes sealed bearings and full fitting
instructions detailing how to swap switches, shaft
etc over from the standard throttle body. This is
a non-exchange item that enables the original throttle
body to be retained. RRP $699.00.
Part # PTB000
|
|
Dual Engine
Covers
Heat retention
is a big problem with attaining optimum performance
from the LS1 engine. Similar to the covers on the
limited edition HSV GTS, the SS Inductions’
dual engine covers not only look great but, just
as importantly, prevent that heat build-up. The
covers are made from high-heat plastic and feature
protective heat shield.
Available in red or black as standard plastic colours
or colour-coded to match your car. RRP from $380.00.
Part # DEC001 (red smooth)
Part # DEC002 (black textured)
|
|
High Performance
Ignition Leads
9mm
Spiral Wire gives lower resistance than standard
leads hence a stronger spark for better performance
and economy. RRP $165.00.
Part # HPL005
|
|
Gauge Holder
This great looking plastic gauge
holder is designed to hold two standard sized gauges
(2 1/16” and 2 5/8”) and is mounted
on the top of the centre dash, pointing toward the
driver. It is available in black or gunmetal grey,
with a smooth finish. RRP $89.90
Part # DGH004 (gunmetal grey)
Part # DGH005 (matte black)
|
|
VY-VZ SS
Ute Rear Infill Panel
The
plastic infill panel for the VY Ute sits between
the rear bumperettes for a one-piece streamlined
appearance and to centre the rear number plate.
Allows easy access to the spare wheel compartment.
The panel is supplied in undercoat for a perfect
colour match from your local painter. RRP $275.00.
Part # VUP002
|
|
